Tubing - FEP - Ozone Compatible

Ozone Solutions

Write a Review
California Regulatory Information

SKU: FP44N30S0-10
SKU:
FP44N30S0-10
Condition:
New

Product Overview

FEP Tubing is the best tubing available for the plumbing of ozone gas. This tubing is completely ozone resistant, can handle high temperatures and is flexible. Ozone Solutions stocks this tubing for our use when building ozone systems and also offers this tubing for sale. Tubing is normally in stock and can ship in 5 foot incremental lengths. 

FEP tubing is a copolymer of TFE, the basic fluoro-monomer building block. The addition of a modifier results in a small, but meaningful departure from the properties of PTFE tubing. Mainly, it possesses a working pressure that is 30% higher, transparent walls, a small increase in stiffness, and a use temperature that is 50 degrees F lower. Unlike other fluoropolymer tubing, long continuous lengths of FEP tubing can also be produced by extrusion. The relatively low cost and desired properties of FEP tubing drives its use in many applications that require high electrical breakdown voltage, low dielectric constant, high chemical resistance, high UV transmission, excellent sterilizability and longevity of use.

FEP tubing is best used with Kynar Fittings which are specially designed to create a tight seal around plastic tubing. These fittings come in a variety of sizes and specifications and are resistant to abrasion and corrosion.

Key Properties:

  • Cost-effective fluoropolymer and alternative to PTFE
  • Excellent UV transmission, electrical, and better mechanical properties than PTFE
  • Longer continuous tubing lengths available compared to PTFE
  • Great for cabling, electrical insulation, water disinfection, environmental, and food contact applications
  • Preferred material where tubing clarity or organization is desired
  • Use temperature of 450 F (~230 C)
 Properties
 Wall Tolerance +/-
0.005 - inch
 OD Tolerance +/-
0.008 - inch
 Burst Pressure @ 75-deg F
840 PSI
 Tensile Strength, 73-deg F
2100 - 3050 PSI
 Elongation, 73-deg F
240 - 300%
 Yield Strength
1740 PSI
 Melting Point
487 - 540 Deg F
 Thermal Conductivity
1.45 Btu·in/h·ft2·°F
 Service Temperature
-418 to 403 Deg F
 O2 Permeability
637 Ng cm m-2

Warranty Information

Seller warrants that all Products will conform to the Specifications and will be free from defects in material workmanship and programming. Claims for Products not complying with this warranty shall be submitted by Buyer no later than 6 months from delivery date to Buyer. Seller shall promptly repair or replace, at its option and expense, non-complying Products. The shipment of non-complying Products by Buyer to Seller, and the return shipment of repaired or replacement Products by Seller to Buyer shall be at Seller's expense, unless it shall be determined that Buyer returned a Product that was in compliance, in which case such cost shall be borne by Buyer and, if paid by Seller, these expenses shall be reimbursed by Buyer within thirty (30) days of notice by Seller. Buyer shall receive a credit for any non-complying Products returned for repair or replacement. All non-complying Products shall be returned to Seller (at its offices or as otherwise instructed) no later than 30 days as of the date the non-compliance of any such Product has been discovered. Seller is NOT responsible for any/all damages suffered to the Products that is caused by the Buyer. Such as but not limited to damage by wrong electrical current, damage through crush or dropping the product, damage through untrained users of Product, damage through improper operations.

California Regulatory Warning

Example Image
Use in unoccupied spaces only.
Health hazard warning: emits ozone.

This product is not CARB Certified (Ozone Emissions for Air Cleaners).
Product Disclaimer: Does not meet California air cleaner regulation requirements; cannot be shipped to California.