Oxygen Concentrator Module - ATF-25

ATF Oxygen Modules incorporate proven pressure swing adsorption (PSA) principles into a unique patented design, which allows these systems to be compact, efficient, rugged, and lower in cost. ATF modules offer unparalleled design flexibility and enable applications where on-site/on-board oxygen generation was previously impractical. 

A patented single rotary distribution valve built into the ATF module continually rotates at low speed by a small motor. The valve is maintenance-free, self-cleaning, insensitive to contamination, and invulnerable to wear. It directs the flow of compressed air to a group of four sieve beds (adsorption), while another four beds are purged into the atmosphere through the valve (desorption). The remaining four of the twelve beds are interconnected through the valve to equalize pressure as the sieve beds sequentially transition between adsorption and desorption. The small amplitutde pressure swings generated by the twelve sieve beds eliminate loud noise pulses, eliminate the need for a pressure regulator, and reduce compressor wear. 

This is an OEM component that will require other ancillary components for operation.

Features

• 25 SCFH Oxygen at 14 PSI from 6.2 CFM compressed air
• Reliable Oxygen Production
• Compact and Lightweight
• Constant Delivery Pressure
• OEM Configuration

More Information
Weight	15.0 lbs (6.8 kg)
Dimensions	Length: 20 in (50.8 cm) Diameter: 8.2 in (20.8 cm)
Warranty	1 Year
Flow Rate (CFM)	6.2 CFM
In Stock	Call For Availability
Max Pressure	14 PSI (0.98 Bar) Max O2 outlet pressure
Oxygen Connection	1/4-inch Barb
Integrated Compressor	No 6.2 CFM @ 35 PSI required
Oxygen Flow Rate	11.8 LPM (25 SCFH)

 

System Information
Input Air Requirements:  Flow  Pressure	175 LPM (6.2 SCFM) 35 PSI (241 kPa)
Performance Data:  Product Flow  Oxygen Delivery Pressure	12 LPM (25 SCFH) 14 PSI (97 kPa)
Product Concentration	90-95%
Product Dew Point	-100°F (-73°C)
Dimensions (DxH)	8 x 20 inches 21 x 51 cm
Weight	15 lbs (6.8 kg)
Physical Connections:  Compressed Air Inlet  Product Gas Outlet	1/2" ID tubing 1/4" ID tubing
Ambient Operating Conditions	Locate the oxygen concentrator system in a well-ventilated area that is protected from weather elements. Inside room or enclosure: Temps should remain between 40°F (4°C) and 130°F (54°C)  In storage: Temps should remain between 0°F (-18°C) and 140°F (60°C)
Control Power Requirements (Single Phase)	120 V / 208-240 V ~ ± 10%, 50 / 60 Hz, 0.025 A or 208-240 V ~ ± 10%, 50 Hz, 0.025A
Typical Power Consumption	3 W
Gear Motor	7350 (FMR 1250) / 7398 (FMR 1268)
Compressed Air Input Requirements	Clean Air (oil-less). Max Temp of 170°F (77°C). Performance Rated at 120°F (49°C).
Mounting	Two Integral Mounting Pads Provided. Toe Clamps (Optional) Vertical Mounting Preferred. Must Be Isolated From Compressor Vibration.

 

ATF-25 Specifications

Seller warrants that all Products will conform to the Specifications and will be free from defects in material workmanship and programming. Claims for Products not complying with this warranty shall be submitted by Buyer no later than 12 months from delivery date to Buyer. Seller shall promptly repair or replace, at its option and expense, non-complying Products. The shipment of non-complying Products by Buyer to Seller, and the return shipment of repaired or replacement Products by Seller to Buyer shall be at Seller's expense, unless it shall be determined that Buyer returned a Product that was in compliance, in which case such cost shall be borne by Buyer and, if paid by Seller, these expenses shall be reimbursed by Buyer within thirty (30) days of notice by Seller. Buyer shall receive a credit for any non-complying Products returned for repair or replacement. All non-complying Products shall be returned to Seller (at its offices or as otherwise instructed) no later than 30 days as of the date the non-compliance of any such Product has been discovered. Seller is NOT responsible for any/all damages suffered to the Products that is caused by the Buyer. Such as but not limited to damage by wrong electrical current, damage through crush or dropping the product, damage through untrained users of Product, damage through improper operations.

All of Ozone Solutions ozone generators are intended for industrial use ONLY within the state of California.
They are to be used in unoccupied spaces only.
Health hazard warning: emits ozone.